| Rating |
| Operating Voltage (Max.) | 50V AC | |
| Current Rating (Max.) | 0.4A DC | *Includes temperature rise due to current flow |
| Operating Temperature Range | -25C ~ +85C | |
| Operating Humidity Range | 90% RH Max. | |
| Storage Temperature Range | -10C ~ +50C | |
| Storage Humidity Range | 90% RH Max. | |
| Electrical Performance |
| Contact Resistance | 40 m Max. | Mate applicable FPC, 20mV Max, 10mA (EIA-364-23) |
| Insulation Resistance | 500 M Min. | Mate applicable FPC, 500V DC between adjacent terminals or ground (EIA-364-21) |
| Dielectric Strength | No Breakdown | Mate applicable FPC, 250V AC (rms) for 1 minute between adjacent terminals or ground (EIA-364-20) |
| Mechanical Performance |
| FPC Retention Force | 0.3N Min. | Insert actuator, pull FPC at 253mm/min |
| Terminal Retention Force | 3N Min. | Apply axial pull out force on terminal at 253mm/min |
| Fitting Nail Retention Force | 1N Min. | Apply axial pull out force on fitting nail at 253mm/min |
| Environmental Performance and Others |
| Durability | Contact Resistance: 60m Max. | Insert and withdraw actuator up to 20 cycles at <10 cycles> |
| Temperature Rise | 30C Max. | Measure contact point temperature rise at max rated current (EIA-364-70 METHOD 2) |
| Vibration | Appearance: No Damage
Contact Resistance: 60m Max.
Discontinuity: 1sec Max. | DC 1mA, 1.5mm displacement, 10-55-10 Hz for 2 hours in X, Y, Z axes (EIA-364-28 Condition I) |
| Shock | Appearance: No Damage
Contact Resistance: 60m Max.
Discontinuity: 1sec Max. | Mate applicable FPC, DC 1mA, 490m/s {50G} for 3 times in 6 directions (EIA-364-27, test condition A) |
| Heat Resistance | Appearance: No Damage
Contact Resistance: 60m Max. | Mate applicable FPC, expose to 852C for 96 hours, then condition at room temp. |
| Cold Resistance | Appearance: No Damage
Contact Resistance: 60m Max. | Mate applicable FPC, expose to -402C for 96 hours, then condition at room temp. |
| Humidity | Appearance: No Damage
Contact Resistance: 60m Max.
Dielectric Strength: No Breakdown
Insulation Resistance: 40 M Min. | Mate applicable FPC, expose to 602C, 90-95% RH for 96 hours, then condition at room temp. |
| Temperature Cycling | Appearance: No Damage
Contact Resistance: 60m Max. | Mate applicable FPC, 5 cycles: a) -553C (30min), b) +853C (30min), then condition at room temp. |
| Salt Spray | Appearance: No Damage
Contact Resistance: 60m Max. | Mate applicable FPC, 51% NaCl, 352C for 484 hours, then wash and dry. |
| SO2 Gas | Appearance: No Damage
Contact Resistance: 60m Max. | Mate applicable FPC, expose to 505 ppm SO2 gas at 402C for 24 hours. |
| NH3 Gas | Appearance: No Damage
Contact Resistance: 60m Max. | Mate applicable FPC, 40 minutes exposure to NH3 gas from 28% Ammonia solution. |
| Solderability | Solder Wetting: 75% min. wetting area, no voids/pinholes. | Immersion at 2455C for 30.5 sec, up to 0.1mm from housing bottom. |
| Resistance to Soldering Heat | Appearance: No Damage | Refer to paragraph 7 for IR reflow; Soldering iron method: 3 sec max, 370-400C. |
